bending steel tubing
"
Труба EFW ERW одиночным сваренная двойным швом
EFW ERW Single Double Seam Welded Pipe Quick detail: Single Seam: Outside Diameter 6-914mm Wall thickness 0.5-60mm Double Seams:Outside Diameter 630-1524mm Wall thickness 2-80mm Circular Seam:Outside Diameter 630 mm above Wall thickness 2-100 Material SUS 304,TP304 SUS304L TP304L SUS316 TP316 SUS316 TP316L. Calculation Formula 0.02491 0.02482 0.02513 Application : Electric Power Oil Refining Nuclear Power Drinking Water Offshore Engineering &Shipbuilding Natural Gas Paper
Вокруг трубы углерода ASTM a 556 TORICH безшовной
ASTM A 556 Seamless Cold-Drawn Carbon Steel Tubes In Tubular Feed Water Heaters This standard is issued under the fixed designation A556/A556M；the number immediately following the designation indicate the year of original adoption or,in the case of revision,the year of last revision. A number in parentheses indicates the year of last reapproval. A superscript epsilon indicates an editorial change since the last revision or reapproval. Scope This specification covers minimum
Безшовное Inconel 625 гидравлических плунжерных штоков
Piston rods made from Inconel 625 For the hydraulic piston rods discussed in Sections 16.2 and 16.3 mechanical loads are combined with tribocorrosion. The high pressure inside the cylinder acts on the seals to ensure a leak-free sealing by means of a uniform distributed seal contact pressing on the piston rod surface. The contact pressure of the seals on the piston rod surface can be in the range of 50 N/mm2 at 160 bar system pressure. If a hard particle is imbedded into the
Высокая труба теплообменного аппарата ASTM A672 Efw давления
ASTM A672 Electric-Fusion-Welded Steel Pipe For High-Pressure Service Heat Exchanger Tube Scope This specification covers steel pipe: electric-fusion-welded with filler metal added, fabricated from pressure-vessel quality plate of any of several analyses and strength levels and suitable for high-pressure service at moderate temperatures.Heat treatment may or may not be required to attain the desired properties or to comply with applicable code requirements.Supplementary
Супер двухшпиндельная 2507 600mm продольная сваренная труба
Super duplex 2507 600mm circumferential weld Double Seam Longitudinal Welded ERW Stainless Steel Pipe /SS Tube Quick detail: Material Super Duplex 2507 Size :600mm Production method : Double Seam ,Circumferential Weld,Double Seam Longitudinal Welded Product name: Stainless steel pipes SS Tube Material Super duplex 2507 Chemical composition: STEEL Grade C≤ Mn≤ Si≤ S≤ P≤ Cr Ni Mo Cu≤ N S32750(2507) 00Cr25Ni7Mo4N 0.03 1.2 0.8 0.02 0.035 24/ 26 6.0/ 8.0 3.0/ 5.0 0.5 0.24/ 0.32
310S 321 904L Ss Erw пускают стандарт по трубам ASTM
Large Diameter Welded Stainless Steel Pipe 310S 321 904L ERW Stainless Steel Pipe Quick detail: Big dimater 6-2000mm Thcikness 0.5-60mm Production method : Single Seam Double Seams Circular Seam ERW Grade: 304 316L 310S 321 2205 904L etc Finish: No-polished/bright polished Large Diameter Welded Stainless Steel Pipe 310S 321 904L ERW Stainless Steel Pipe Description: Material Austenitic Stainless Steel 310S, 309S,316L,321,304L,304 Duplex S,32750,S32760,S31803,S32205 Nickel
Труба большого диаметра Torich длины AISI 18m сваренная
14” X ray test straight slit circumferential weld Circumferential welding of gas pipeline WELDED LARGE DIAMETER PIPE Quick detail: Single Seam: Outside Diameter 6-914mm Wall thickness 0.5-60mm Double Seams:Outside Diameter 630-1524mm Wall thickness 2-80mm Circular Seam:Outside Diameter 630 mm above Wall thickness 2-100 1/2 inch NB to 16 inch NB Description: Material 304/304L/304H(1.4301/1.4306/1.4948) 316L(1.4401/1.4404); 316Ti(1.4571); 321(1.4541); 309S 316/(1.4833); 310S(1
ASME B16.9 10" редуктор безшовное DN6 DN100 сварного соединения встык концентрический
ASME B16.9 Concentric Reducer Standard ASME B16.9 wraps in several parameters that act as a guideline for the manufacturer of wrought factory-made buttwelding fittings such as elbows, tees, reducers including the Carbon Steel Concentric Reducer etc. The fittings need to conform to the values of the following parameters i.e. overall concentric pipe reducer dimensions, ratings, testing, tolerances, and markings. Depending on the buyer, these reducers are made available between
